Space Force

space-force-front.jpg
space-force-angle.jpg
space-force-front.jpg
space-force-angle.jpg

Space Force

$229.99

Mankind has long known of the amazing properties of reverberant spaces. From the brilliant reflections of the largest concert halls to the splashy depths of your own shower, every space has its own characteristic sound.

The Space Force is our updated take on the sounds of “elsewhere,” and features eight ingenious ways to add some space to your place, whether you're reaching for the stars or just trying to make your world a little bigger.

Quantity:
Add To Cart

Reverb is a pretty subjective thing - sometimes you need a soft and subtle bloom behind your notes, and sometimes you really need to wail at the bottom of a stone well. The Space Force gives you a ton of options, all of which you can tweak and customize to suit your desires using our simple knob interface.

The Leap Series improves upon our popular Neo Series platform in lots of ways, including:

  • Stereo audio input and output with phase correction

  • Low-noise direct-coupled audio path

  • Improved audio headroom and frequency response

  • FXCore DSP with more than 8 times the processing power than our previous Neo Series pedals

  • 32 onboard presets (4 banks of 8 presets each,) all accessible on the pedal without the need for external controls.

Space Force features eight all-new reverb engines, each with its own set of tweakable parameters.

REVERB ENGINES:

PLATE: Based on a vintage studio reverb, this simulates the reflective properties of a giant metal plate. We’ve also included a virtual tape pre-delay and adjustable tape flanging modulation.

MOD HALL: Classic 1980s electronic hall reverb with adjustable pitch modulation. We’ve added high and low EQ controls to allow for fine-tuning the reverb tone.

PITCH: Chamber reverb effect with twin adjustable pitch shifters. Each shifter has selectable intervals ranging from a detune effect to an octave. Try with detune or down an octave for a cool textural wash.

SPRING: Surf’s up! Spring reverb effect with multi-wave tube bias type tremolo. We’ve placed the tremolo after the reverb to ensure that it stays juicy no matter how wet you run the springs.

LO-FI: 1990s style electronic reverb with distortion on the reverb trails. Classic “shoegaze” effect, try this with the SAW modulation to simulate whammy bar guitar.

ANALOG: “Electronic” reverb based on an obsolete analog delay chip, these units were often used in karaoke machines and have a distinctive tone. Keep the time knob low for reverb or increase for cascading delay effects.

DYNAMIC: Large cathedral-style reverb with a volume-sensing fade effect. GATE mode will cut off the reverb like ‘80s drums, BLOOM will fade in just the reverb signal, and SWELL fades in both wet and dry for a more intense effect.

ECHOVERB: Room reverb and delay in parallel. Each effect has its own set of controls and is independent. The delay effect works even when the reverb effect is in the HOLD / FREEZE state.

PRESETS

THIRTY-TWO built-in presets (four banks of 8) allow you to colour with all the crayons in the box. Hold the Bypass / Preset footswitch to select the next preset, or hold both footswitches for the previous.

BYPASS TRAILS

The reverb + delay trails are configurable for hard bypass, full trails, or auto trails. In auto trails mode, the reverb will decay normally and then seamlessly ramp to zero volume for the lowest possible operating noise.

EXPRESSION AND RAMPING

Seamlessly morph between different knob settings on the fly using the built-in ramp footswitch, expression pedal, footswitch, or MIDI controller.

STEREO INS AND OUTS

The input jack is selectable for standard mono or TRS stereo signal input without opening the pedal. The output jacks are usable as either mono, two-cable stereo, or TRS stereo. Connect all your Venture and Leap Series pedals in stereo with TRS cables for a neat and tidy pedalboard!

MULTIJACK

Connect an expression pedal, footswitch, or MIDI controller to this jack to add performance control to your pedal.


USB PORT

Every Leap Series pedal features a USB port for MIDI control and firmware updates.

Mono or stereo input (TRS)

Mono or stereo output (TRS or dual outputs)

Input Impedance: 1M ohms

Output Impedance: 560 ohms

DC 9V only, 250mA or greater

Requires isolated DC power supply

4.7” x 2.6” x 1.5” H x W x D not including knobs

Eight reverb engines

32 user presets, arranged in 4 banks of 8

MultiJack enables expression pedal, foot switch, or MIDI input

EXP Morph allows controlling all knobs from expression pedal, ramp footswitch, or MIDI

Automatic ramping function for expression control without external pedal

CTL footswitch for tap tempo and ramp trigger

USB port for firmware updates and USB MIDI

Buffered bypass

User Manual and firmware are available here.